Roll Bar/ Sports Bar - Suitable For Ford Ranger PX1/PX2/PX3/PX4
Stops the load shifting around the Ford Ranger tray and gives the back of the ute the stance it was missing, with mounting points already built in.
- 30-day returns
- Warranty against defects
- Ships from our Auckland warehouse
BUILT FOR THE WHOLE TRAY.
A roll bar earns its keep the day you actually load the tray, it's the difference between gear shifting around and gear staying put.
STOPS A SHIFTING LOAD
Backstops your tray load under hard braking, the actual job, not just the look.
MOUNTING POINTS BUILT IN
Pre-drilled points for a UHF aerial, worklights or a flag pole, no new holes needed.
BOLT-ON, NO DRILLING
Bolts to factory tray mounting points.
CHOOSE THE SPAN THAT SUITS YOUR SETUP.
Both do the same load-protection job. The difference is mounting width for bigger accessories.
FORD RANGER ROLL BAR
Standard mounting span for a UHF aerial, worklights or a flag pole.
FORD RANGER ROLL BAR (EXTENDED ARMS)
Wider mounting span for a bigger light bar or a roof-tent annexe.
FITTING IS STRAIGHTFORWARD.
Bolts to factory tray mounting points, no drilling into the tub.
BOLT-ON FITMENT
Mounts using the vehicle's factory mounting points.
NO DRILLING
Bolts to factory tray mounting points, no drilling into the tub.
HARDWARE SUPPLIED
All hardware needed for installation is included in the box.
CHECK THE FIT
Offer the part up before final fitting to confirm alignment.
COMMON QUESTIONS
Will this fit my Ford Ranger?
This is made for the Ford Ranger specifically, not a universal part trimmed to suit. It is listed to fit PX1 2012–15 · PX2 2016–18 · PX3 2019–21 · PX4 2022–26.
Model runs change part way through a year, so if your vehicle sits near the edge of that range, send us your rego or VIN and we will confirm the fitment before you order rather than after.
Will it work with a tonneau, hard lid or canopy?
It mounts into the tray, so it comes down to where your lid or cover sits and how far forward it opens. Some combinations work as-is and some need the cover adjusted.
Tell us exactly what you have on the back now and we will tell you before you order, rather than you finding out in the driveway.
How does it mount, and can I hang gear off it?
It bolts into the tray using the supplied hardware, and the mounting points for lights and tie-downs are already built into the bar rather than something you drill later.
It is a two-person lift. Anything you mount high changes how the load sits, so keep heavy gear low and check your tie-downs after the first run.
If you would rather not do it yourself, our own team fits these in-house at our Avondale workshop. Call 021 541 306 to book a time.
How fast will it get to me?
Orders placed on a business day are usually picked and dispatched the same or the next business day from our own Auckland warehouse, and you get tracking by email as soon as it leaves us.
From the day it ships, North Island urban addresses are generally overnight and South Island urban is 2 to 3 business days. Rural addresses take a little longer. You can also choose pickup at checkout and collect from our Avondale store once we email to say it is ready.
What happens if it does not fit, or I change my mind?
You can return any unused, uninstalled item in its original packaging within 30 days of delivery for a refund or an exchange, and there is no restocking fee. Ordering the wrong part, or finding it does not suit your vehicle, is covered.
Email info@toughtrucks.nz or call 021 541 306 before you send anything back so we can confirm the return and give you the correct address. Once it is back with us and checked, refunds go through within 5 business days.
Still not sure it is the right part? Call 021 541 306 or email info@toughtrucks.nz with your rego and we will confirm fitment before you order.
BUILT FOR YOUR UTE.
HEAVY-GAUGE STEEL construction, vehicle-specific fitment and straightforward installation.